Rear air suspension
Turn the car with your finger. Drive it on a road, add load, or set a fault. See how the pressure in each air spring changes. Tap a part to read about it.
The parts
What the system does
Two air springs hold up the rear of the car. They replace the steel coil springs. The front axle keeps its steel springs.
A height sensor on each side measures the distance between the body and the axle. The control unit compares the height with a target. If the body is too low, the control unit starts the compressor and opens a valve. Air goes into the spring and the body goes up. If the body is too high, the control unit releases air.
When the height is correct, all valves are closed. The air stays in the springs. A good system holds its height for many days with the engine off.
What happens on the road
During driving the valves are closed. No air goes in or out of the springs. But the pressure changes all the time, because the volume of each spring changes.
- Bump: the wheel goes up, the spring gets shorter, and the same air has less space. The pressure goes up and pushes the wheel down again.
- Pothole: the wheel goes down, the spring gets longer, and the pressure goes down. Then the wheel hits the far edge of the hole and the pressure goes up sharply.
- One wheel: the spring on the other side changes only a little. The body turns a small quantity around its length axis.
- Speed bump: the two springs get shorter at the same time. The body goes up and comes down again. The shock absorbers stop this movement after one or two cycles.
The Air view shows this. Each dot is a quantity of air. When the spring gets shorter, the same dots have less space: they pack closer, move faster and change colour from blue (low pressure) through amber to red (high pressure). When the compressor fills a spring, new dots flow in through the valve. When the control unit releases air, dots flow out through the exhaust. A leak lets dots escape from the side of the bellows.
Add load and do the test again. The pressure in the springs is higher, and the pressure changes are larger.
Three tests in the model
- Move the load to 400 kg. The body goes down. Then the compressor lifts it to the target.
- Select Left spring leaks. Look at the compressor. It starts again and again. Then tap Park for 8 hours and start the engine.
- Select Left sensor is wrong. The car leans, but there is no leak. The control unit thinks that the height is correct.
From symptom to part
Before you work on the car
- Do not open an air line when there is pressure in the system. Release the pressure with a BMW diagnostic tool first.
- Put the body on stands. Do not let the air springs hold the car while you work below it.
- Find leaks with water and soap. Bubbles show the leak.
- Repair the leak before you replace a compressor. A leak makes a new compressor wear out quickly.
- When you replace the compressor, replace the relay also.
In VR (Meta Quest)
- Open the page in the Quest browser and push Enter VR. The car is at its real size.
- Point with a controller or your hand. Push the trigger or pinch to use a button or to select a part.
- Left thumbstick: move. Right thumbstick left or right: turn in steps. Right thumbstick up or down: move up or down.
- Use On a lift to stand below the car and look up at the springs.
- Point at a panel and hold the grip button to move the panel. Release the grip to put it down.
- Hold the two grip buttons, then move your hands apart to take the car apart. Move them together to assemble it. You can stop at any point between.
- If the moving road makes you feel bad, look at the light disk below your feet, or select Parked.
Copilot
A second device sees the car of the pilot and changes the settings. Example: you wear the Quest, and a friend uses the MacBook.
- On the Quest, read the code of 6 digits. It is at the top of the VR control panel, and in the copilot box on the page.
- On the Mac, open the same page. Type the code in the copilot box and push BE COPILOT.
- The Mac shows the car of the pilot. Pilot view shows what the pilot sees. Free view lets you turn the car. In free view you also see the head of the pilot and where the pilot points.
- All controls on the Mac (road, load, faults, parts, body) change the car of the pilot.
- STOP COPILOT makes the Mac a normal device again.
A public server (PeerJS) helps the two devices to find each other. After that the data goes directly between the devices. On the same WiFi it stays in your network.
Keys
- E take apart or assemble
- B body: x-ray, paint, or off
- U look from below
- V home view
- P park for 8 hours
- S engine on or off
- 0 to 5 select a fault
- Q W R T Y select the road
- A show or hide the air
- C copilot: pilot view or free view
- H make the copilot box small
This is a simplified model. The pressures, times, and heights are examples and are not BMW data. The body is a simple dark blue SUV shape with the approximate dimensions of the F15. It is not a copy of the BMW design and it has no BMW marks. The shapes and positions of the parts are schematic. Use the repair data for your VIN before you buy parts. Source for the fault list and the checks: SSF Autofocus, F15/F16 suspension.